trouble reassembling smith and wesson 915

#Trouble reassembling smith and wesson 915 how to
#Trouble reassembling smith and wesson 915 full
#Trouble reassembling smith and wesson 915 professional

Do not disassemble them outside of your disassembly box! If you have a digital camera, you may want to take a few photographs along the way. Remove the hammer and trigger assemblies as complete assemblies. I simply place the gun inside, drop the cloth over my hands, and voila! When the spring pops out, it is caught. Nothing wastes time like trying to find a miniscule spring that leaped across the room, let alone not even knowing what happened and wondering why your gun doesn't work anymore! For disassembly I use a ten gallon acrylic aquarium turned on it's side with a cloth over it's opening. I have also attached a small wooden bowl to hold small springs, pins and such while I work. In fact, I have an area with a diagram of a S&W sideplate with the screw pattern drilled, so I do not mix up yoke screws with the other screws. I attached rubber feet to it's underside to keep it from skidding, I drilled holes in it to allow me to punch out pins and to keep screws in order. Thus, I purchased a large wooden cutting board to function as a workspace on any counter or table I choose. A gunsmithing table is nice, but I have learned that such a wonderful space quickly becomes cluttered in my world. Here are a few of my tricks I have learned along the way. If you do, do not blame me for the results! Do not start out on your three and a half inch Model 27. Buy the ugliest, cheapest S&W you can find that still has a functional trigger and hammer. Purchase a beater revolver to be your first sacrificial lamb. If it sounds like a non-damaging or reversible trick, give it a try. If the information conflicts with Jerry K, then eschew it. Cruise the various gunsmithing forums and listen to what the old established posters have to say. Buy Jerry Kuhnhausen's The S & W Revolver: A Shop Manual.

#Trouble reassembling smith and wesson 915 full

As soon as they say 'Just pry the sideplate off' you know they are full of hog manure. If you are unwilling to invest in the proper tools, then you are unwilling to do the job right.ĭo not rely on what the gun counter commando tells you. The proper tools include at the minimum, a small set of gunsmith screwdrivers, of high quality sized for Smith & Wesson revolvers. That is enough, as long as the proper checks are performed before firing the weapon again.ĭo not try to open up your Smith with Grandpa's old twenty-nine cent screwdriver and Granny's butterknife. I am a self taught wrench turner who knows to watch how things come apart, and when to go to the manual. My own experience is a mechanical aptitude that ranges from Model T speedsters to F-18 fighter jets.

#Trouble reassembling smith and wesson 915 professional

On the other hand, if you are a professional watchmaker, you will pick it up with no problem.

#Trouble reassembling smith and wesson 915 how to

If you are unable to jump start your car, or you cannot figure out how to plunger a toilet, then disassembling a S&W is not your game. Disassembly and reassembly requires an eye that has a bit of mechanical aptitude, and a mind grounded in common sense. The tolerances of a S&W are precise, however. The lockwork of a Smith & Wesson revolver is not particularly delicate, although there are a couple of small springs that can pop out at inopportune times for the uninitiated. So, here are my thoughts on the subject of cracking open a Smith and Wesson revolver: Still, being one who advocates buying used, older revolvers, I would be remiss if I did not pass out a bit of information. Also, some of my own technique is contrary to conventional wisdom. The risk of giving somebody just enough information to make a gun dangerous is extremely high. My policy has always been to avoid those questions. I have often been asked to demonstrate/illustrate how to open up and clean a Smith & Wesson revolver.